![[object Object]](https://omo-oss-image.thefastimg.com/portal-saas/pg2026063019375911813/cms/image/138ba837-b50d-4ff3-a73c-2e6a2379c522.jpg "[object Object]")
PRODUCTS CENTER
Brazil Acrel ADW600 CE IEC Approved Wireless 4G Digital 3 Phase Multi-channel Energy Meter For IOT Platform Energy Consumption Monitoring
Category:
Product Description
Overview
The ADW600 multi-circuit power metering module is mainly used to measure three-phase active energy in low-voltage networks, and has the advantages of small size, easy installation, and rich functions.
The product adopts a modular design, including voltage module, current module, switch module, temperature measurement and leakage module, etc.
The modules are connected by Ethernet cables and can support multi circuit splicing. Suitable for low-voltage side multi circuit metering scenarios, especially for power transformation needs.
Coding Rule
ADW600 main module
ADW600 slave module
Dispaly
Models & Function
|
model |
Functional Description |
|
ADW600-U |
Voltage measurement and sampling |
|
ADW600-I |
Active energy measurement (forward and reverse), Four-quadrant reactive energy |
|
Voltage, current, power factor, frequency, active power, reactive power, apparent power |
|
|
Total harmonic content, sub-harmonic content (2nd to 31st) |
|
|
Active pulse output |
|
|
ADW600-K |
4DI, 2DO |
|
ADW600-TL |
4 channels for temperature measurement, 1 channel for residual current measurement |
Network
Dimension
1. The ADW600-M gateway (-4G/-CE/-WF) on the far left of the ADW600 rendering in Figure 1 needs to be ordered separately.
2. When connecting network cables between different modules, please note that BUS-IN is the incoming interface and BUS-OUT is the outgoing interface. Start with ADW600-M or th power module and connect them in sequence. Do not connect them in reverse.
|
Model |
Dimension（mm） |
Hole size（mm） |
Tolerance（mm） |
|||||
|
W |
H |
D |
M |
N |
Φ1 |
Φ2 |
||
|
D10：AKH-0.66/K-∅10N |
27 |
44 |
32 |
25 |
36 |
10 |
9 |
±1 |
|
D16：AKH-0.66/K-∅16N |
31 |
50 |
36 |
27 |
42 |
16 |
17 |
|
|
D24：AKH-0.66/K-∅24N |
39 |
71 |
46 |
36 |
52 |
24 |
23.5 |
|
|
D36：AKH-0.66/K-∅36N |
42.5 |
82 |
58 |
40 |
56 |
33.5 |
35 |
|
Wiring
ADW600 multi-circuit metering modules are connected by network cables. BUS-IN is the incoming interface and BUS-OUT is the outgoing interface. They are connected starting from ADW600-M or the power module and cannot be connected in reverse.
ADW600 -U needs to be connected to the load voltage signal. Refer to the wiring diagram below. Terminals 11-14 are connected to the UA, UB, UC, and UN voltage signals respectively. If the three-phase three-wire connection method is used, terminals 11-13 are connected to the UA, UB, and UC voltage signals, and then UB is short-circuited into the UN terminal.
ADW600 -I needs to be connected to the load current signal. Refer to the wiring diagram below. The standard transformer is an RJ12 interface that can be inserted into the meter terminal. The three transformers can be clipped onto the load cables according to the indicated directions.
ADW600 -K is connected to the switch input or output signal line as needed. Note that the COM port is the common end. Refer to the wiring diagram below.
ADW600 -TL is connected to the temperature measurement signal line or the residual current transformer signal line as needed. Note that the COM port is the common end of the adjacent measurement circuits. The specific wiring diagram is as follows.
Newsletter
Sign up our newsletter to get update news and article about company.
