![[object Object]](https://omo-oss-image.thefastimg.com/portal-saas/new2023080419495759710/cms/image/138ba837-b50d-4ff3-a73c-2e6a2379c522.jpg "[object Object]")
Acrel ATC600-Z Wireless Repeater for Cable/Busbar Temperature Monitoring
Series of products: Products
Series of products: Wireless Temperature and Humidity Monitoring
- Product Description
- Parameters
- Q&A
- Download
-
Coding Rule
Dispaly
Function
● Matching Sensors: ATE400, AHE100, ACE100, ATE300P
● Auxiliary power supply: AC/DC100-265V; DC12-48V
● Power: ≤ 2W
● Accuracy: ±1 ℃
● Frequency band: 470 MHz
● Temperature points: 240 points
● Resolution: 0.1 ℃
● Range of temperature measuring: -50 ℃-125 ℃
● Communication distance: 150 m (in open area)
● Communication: RS485(Modbus-RTU)
Application
1. Cable connector temperature measurement; 2. Contact temperature measurement; 3. Busbar temperature measurement
Technical Parameters
型号
Models
参数
Parameters
ATC600-C
ATC600-Z
ATC600-M
功能
Function
接收器
Receiver
中继器（信号放大器）
Repeater(Signal Booster)
接收器
Receiver
匹配传感器
Matching sensors
ATE100/100P;ATE100M;
ATE200/200P;ATE400;
AHE100;ACE100;ATE300P
ATE100/100P;ATE100M;
ATE200/200P;ATE400
ATE300M
工作电源
Power source
AC/DC100~265V；DC12~48V
功耗
Power Consumption
≤2W
测温点数
Temperature points
240点
240 points
——
1440点（240个传感器）
1440 points
（240 Sensors）
分辨率
Resolution
0.1℃
——
0.1℃
测温范围
Range of temperature
-50℃~+125℃
——
-40℃~+140℃
测温精度
Precision
±1℃
——
±1℃
无线频率
Wireless frequency
470Mhz
470Mhz
433Mhz~510Mhz
无线距离
Wireless distance
接收传感器150m（空旷）；接收中继器距离1km（空旷）
Receiving sensor 150m (in open area)；Receiving repeater 1km
(in open area)
接收传感器150m（空旷），中继转发距离1km（空旷）
Receiving sensor 150m (in open area)；Realy distance 1km
(in open area)
接收传感器1km（空旷）
Receiving sensor 1km (in open area)
通讯端口
Communication
RS485
波特率(bps)
Baud rate (bps)
2400、4800、9600、19200
协议
Protocol
MODBUS-RTU
——
MODBUS-RTU
继电器输出
Relay output
2路无源出口，容量5A/AC250V，5A/DC30V
2 passive output，capacity 5A/AC250V，5A/DC30V
工作环境
Environment
温度：-20 ℃～+55 ℃；相对湿度≤95%
Temperature:-20 ℃～+55 ℃；Humidity:≤95%
Network
Solution 1: Wireless temperature measurement of electrical contacts in high and low voltage cabinets
Solution 2: Wireless temperature measurement of electrical contacts in high and low voltage cabinets
Solution 3: On-site wall-mounted centralized display solution
Solution 4: Upload data to IOT Platform
Solution 5: Upload data to IOT Platform
Dimension & Installation
ATC600 wireless temperature transceiver adopt guide rail (DIN35mm) installation，main dimension 90mm*90mm*38mm.
FAQ
1. Is there any signal interference if more than 40 ACREL units are installed?
Reply: No.
2. How to determine the ID of each sensor which is more than 40 units?
Reply: Every sensor sends the temperature data and its ID to ATC600, then transmits to ATP display screen and IOT platform.
ATP dispaly screen and IOT platform can display the data and position of every sensor. The user can identify them easily.
3. How to make sure the battery can last up to 5 years?
Reply: 5 years is the theoretical value calculated by the average current of the sensor. In actual use, it will be affected by various external factors, for example, the battery life will be greatly shortened under the condition of high temperature for a long time.
4. If the battery runs out in less than 1 year, what is the solution? 如果电池在1年内损坏或者电量耗尽，该怎么处理？
Reply: There are 2 solutions:
1. The batteries in the ATE and AHE sensors can be replaced by new ones.
For ATE100M/200/200P, the Battery model is ER2450T.
You have to welding the two points in the sensor when you change their batteries.
For ATE400, it is strap mounted type, powered through electro-magnetic induction, it has no battery.
For AHE100, its battery model is CR2450, the sensor has battery holder, so the battery is easier to be replaced.
2. We can send new sensors to replace those ones with quality problems.
5. Ensure the receiver's ability to read how many sensor units?
Reply: One ATC600-C can read the data of 240 sensors at most.
One ARTM-Pn can read the data of 60 sensors at most.
6. The current condition is that there are 4 receivers that will be installed, to ensure communication between receivers is not disrupted, for example: receiver 1 must read sensors in building 1, but sensors in building 2 are also read?
Reply: Every transceiver will only display the data of the sensors with the corresponding group number, and even if it receives data from other groups of sensors, it does not matter because each sensor has a unique ID and does not cause confusion.
7. What spare parts are available for the spare sensor unit?
Reply: Transceiver has antenna, connection terminals, ATE400 comes with alloy plate, non-slip pad, locking piece and screws.
8. How to distinguish AHE100 and ATE100M/ATE200 type sensor ID? is it enough with 1 receiver?
Reply: The answer is the same with that of the 2nd question.
Yes, it is enough with 1 receiver.
9. Do i have to send commands to the sensor for getting its temperature readings or it keeps sending temperature data automatically when connected?
Reply: ATE400 sensor monitor the data and uploaded it to ATC600 and IOT every 15 S.
ATE400 monitor tenperature and transmits the data every 15 s, it has nothing to do with temperature fluctuationi.
ATE100/200 and AHE100 measure the temperature every 25S. If the temperature changes more than 4 degrees from the previous temperature, the data will be uploaded to ATC600 and IOT. If the temperature changes less than 4 degrees, the temperature will be uploaded every 5 minutes.
if the temperature fluctuation is less than 4 ℃, is transmits every 5 minutes; if it is large than 4 ℃， it transmits every 25 s.
10. How I should interpret the data when I connect the ATC600 directly to the PC (though RS485)? For example, how I identify each sensor with their respective temp?
Register addresses and sensor codes correspond sequentially, one to one
Other Question? Please contact us and we will get back to you as soon as possible.
Product Description:- PView
- high-performance
- requirements
-
Technical Features
型号
Models
参数
Parameters
ATC600-C
ATC600-Z
ATC600-M
功能
Function
接收器
Receiver
中继器（信号放大器）
Repeater(Signal Booster)
接收器
Receiver
匹配传感器
Matching sensors
ATE100/100P;ATE100M;
ATE200/200P;ATE400;
AHE100;ACE100;ATE300P
ATE100/100P;ATE100M;
ATE200/200P;ATE400
ATE300M
工作电源
Power source
AC/DC100~265V；DC12~48V
功耗
Power Consumption
≤2W
测温点数
Temperature points
240点
240 points
——
1440点（240个传感器）
1440 points
（240 Sensors）
分辨率
Resolution
0.1℃
——
0.1℃
测温范围
Range of temperature
-50℃~+125℃
——
-40℃~+140℃
测温精度
Precision
±1℃
——
±1℃
无线频率
Wireless frequency
470Mhz
470Mhz
433Mhz~510Mhz
无线距离
Wireless distance
接收传感器150m（空旷）；接收中继器距离1km（空旷）
Receiving sensor 150m (in open area)；Receiving repeater 1km
(in open area)
接收传感器150m（空旷），中继转发距离1km（空旷）
Receiving sensor 150m (in open area)；Realy distance 1km
(in open area)
接收传感器1km（空旷）
Receiving sensor 1km (in open area)
通讯端口
Communication
RS485
波特率(bps)
Baud rate (bps)
2400、4800、9600、19200
协议
Protocol
MODBUS-RTU
——
MODBUS-RTU
继电器输出
Relay output
2路无源出口，容量5A/AC250V，5A/DC30V
2 passive output，capacity 5A/AC250V，5A/DC30V
工作环境
Environment
温度：-20 ℃～+55 ℃；相对湿度≤95%
Temperature:-20 ℃～+55 ℃；Humidity:≤95%
项目
Items
指标
Features
环境要求
Environment
工作温度
Temperature
-40℃~85℃
相对湿度
Humidity
≤95%
大气压力
86kPa~106kPa
ATE100M/100/200有源无线温度传感器
ATE100M/100/200 Active wireless temperature sensor
无线频率
Wireless frequency
470MHz、433Mhz
通讯距离
Communication distance
空旷150m（470Mhz）、空旷50m（433Mhz）
150m(470Mhz) 、50m(433Mhz)in open area
采样频率
Sampling frequency
25s
发射频率
Transmitting frequency
25s-5min
工作电源
Power source
电池
Battery
安装方式
Installation
磁吸式/螺栓式/表带式
Magnetic / bolted /Belt
测温范围
Range of temperature
-50℃~+125℃
精度
Precision
±1℃
应用范围
Application
高低压柜内电气接头
Joints in high or low voltage switchgears
电池寿命
Battery life
≥5年(25℃)
≥5 years(25℃)
400无源无线温度传感器
400 Passive wireless temperature sensor
无线频率
Wireless frequency
470MHz、433Mhz
通讯距离
Communication distance
空旷150m（470Mhz）、空旷50m（433Mhz）
150m(470Mhz) 、50m(433Mhz)in open area
采样频率
Sampling frequency
15s
发射频率
Transmission frequency
15s
工作电源
Power source
CT感应取电，启动电流≥5A
CT-powered, starting current≥5A
最大工作电流(Max current)≤5000A
安装方式
Installation
合金片固定
alloy chip fixing
传感器探头
Sensor probe
合金底座
alloy bottom
测温范围
Range of temperature
-50℃~125℃
精度
Precision
±1℃
应用范围
Application
高低压柜内电气接头
Joints in high or low voltage switchgears
ATE100P/200P户外无线温度传感器
ATE100P/200P Outdoor wireless temperature sensor
无线频率
Wireless frequency
470MHz、433Mhz
通讯距离
Communication distance
空旷150m（470Mhz）、空旷50m（433Mhz）
150m(470Mhz) 、50m(433Mhz)in open area
采样频率
Sampling frequency
25s
发射频率
Transmitting frequency
25s-5min
工作电源
Power source
电池
Battery
安装方式
Installation
螺栓式/表带式
bolted /Belt
测温范围
Range of temperature
-50℃~+150℃
精度
Precision
±0.5℃
应用范围
Application
电气接头
Voltage switchgears
电池寿命
Battery life
≥5年(25℃)
≥5 years(25℃)
防护等级
Protection level
IP68
ATE300M多回路式温度传感器
ATE300M multi
Loop temperature sensor
无线频率
Wireless frequency
433-510MHz
通讯距离
Communication distance
空旷1000m
1000m in open area
采集频率
Sampling frequency
1-240s
工作电源
Power source
AC/DC 85~265V
安装方式
Installation
导轨式/扎带式
测温范围
Range of temperature
-40℃~+140℃
精度
Precision
±1℃
应用范围
Application
低压抽屉柜内电气接头
Joints in low voltage switchgears
-
1. Is there any signal interference if more than 40 ACREL units are installed?
Reply: No.
2. How to determine the ID of each sensor which is more than 40 units?
Reply: Every sensor sends the temperature data and its ID to ATC600, then transmits to ATP display screen and IOT platform.
ATP dispaly screen and IOT platform can display the data and position of every sensor. The user can identify them easily.
3. How to make sure the battery can last up to 5 years?
Reply: 5 years is the theoretical value calculated by the average current of the sensor. In actual use, it will be affected by various external factors, for example, the battery life will be greatly shortened under the condition of high temperature for a long time.
4. If the battery runs out in less than 1 year, what is the solution? 如果电池在1年内损坏或者电量耗尽，该怎么处理？
Reply: There are 2 solutions:
1. The batteries in the ATE and AHE sensors can be replaced by new ones.
For ATE100M/200/200P, the Battery model is ER2450T.
You have to welding the two points in the sensor when you change their batteries.
For ATE400, it is strap mounted type, powered through electro-magnetic induction, it has no battery.
For AHE100, its battery model is CR2450, the sensor has battery holder, so the battery is easier to be replaced.
2. We can send new sensors to replace those ones with quality problems.
5. Ensure the receiver's ability to read how many sensor units?
Reply: One ATC600-C can read the data of 240 sensors at most.
One ARTM-Pn can read the data of 60 sensors at most.
6. The current condition is that there are 4 receivers that will be installed, to ensure communication between receivers is not disrupted, for example: receiver 1 must read sensors in building 1, but sensors in building 2 are also read?
Reply: Every transceiver will only display the data of the sensors with the corresponding group number, and even if it receives data from other groups of sensors, it does not matter because each sensor has a unique ID and does not cause confusion.
7. What spare parts are available for the spare sensor unit?
Reply: Transceiver has antenna, connection terminals, ATE400 comes with alloy plate, non-slip pad, locking piece and screws.
8. How to distinguish AHE100 and ATE100M/ATE200 type sensor ID? is it enough with 1 receiver?
Reply: The answer is the same with that of the 2nd question.
Yes, it is enough with 1 receiver.
9. Do i have to send commands to the sensor for getting its temperature readings or it keeps sending temperature data automatically when connected?
Reply: ATE400 sensor monitor the data and uploaded it to ATC600 and IOT every 15 S.
ATE400 monitor tenperature and transmits the data every 15 s, it has nothing to do with temperature fluctuationi.
ATE100/200 and AHE100 measure the temperature every 25S. If the temperature changes more than 4 degrees from the previous temperature, the data will be uploaded to ATC600 and IOT. If the temperature changes less than 4 degrees, the temperature will be uploaded every 5 minutes.
if the temperature fluctuation is less than 4 ℃, is transmits every 5 minutes; if it is large than 4 ℃， it transmits every 25 s.
10. How I should interpret the data when I connect the ATC600 directly to the PC (though RS485)? For example, how I identify each sensor with their respective temp?
Register addresses and sensor codes correspond sequentially, one to one
Other Question? Please contact us and we will get back to you as soon as possible.
Related Products
Product inquiry
We will contact you within one working day. Please pay attention to your email.
Newsletter
Sign up our newsletter to get update news and article about company.
